How to Wire the Switch on an Old Patton Fan
How to Install and Connect a Electrical condenser in a Ceiling Fan?
If you ever face a problem with the ceiling fan such as hum interference, slow speed, non running the fan or fan light kit is working but fan has been obstructed steady with proper power append, then you are the correctly forum as one of the most common intellect is a severe or blown capacitor or else of faulty internal windings, power supply failure operating room jam bearings. You may check and examine the capacitor by 6 methods if is faulty or in good specify.
Simply to the point, there is a single form (split phase induction) motor in ceiling fan where we need a starting capacitor to rent the phase betwixt starting and running windings to produce a flux. A capacitor just do it As it provide leading phase shift aside 90° (as some current flow through the staring wandering). This way, potential across staring and lengthways windings have difference phase which provide rotating magnetic filed leading to the rotation of motor rotor coil.
As mentioned preceding and shown in common fig tree below, there are two twisting in a ceiling fan motor which called Main Winding (Running) and Auxiliary (Starting) Winding. We need to connect the capacitor to the opening winding (auxiliary) in series. The neutral should be connected to the inert. Don't forget to link the earth telegraph to the proper grounding and earthing.
- Related Post: What is the Role of Capacitor in a Ceiling Fan?
Note: The wiring colors in this tutorials are for illustration and clarification only i.e. these colors used in this guide is entirely for guidance and do non necessarily represent regional variance. See the bottom notes for America and EU Wiring color codes (NEC and IEC). In addition, some manufactures may use disparate wire colors, this way follow the regional colouring material cryptography operating theater check the user extremity pathfinder for clear account. If inactive not sure, contact a licensed electrician for proper installation.
Disclaimer: This diagrams(s) are to live used as a guide only. Manipulation of this guide is at the installer risk. We Electrical Technology and the author of this guide accept none liability for hurt, loss or damage resulting from function of this run. For fitting installation, you may contact the licensed electrical. Read with kid gloves the safety precaution at oddment of this head.
Now, If we got a faulty capacitor, we may change it by three antithetic ways as follow.
- Replacing a faulty capacitance in a ceiling fan.
- Wiring a Starting capacitor with Cap fan.
- Conjunctive a 3-in-1 condenser with ceiling rooter, reverse switch and pull chain string.
Related Post: How to Size and Determine the Numbers of Ceiling Fan in a Room?
Replacing a Faulty Capacitor in a Ceiling Fan
Suppose a simple fan without light kit need to be replaced with a new employed condenser having the same evaluation, follow the instruction below:
- First off all, change cancelled the main breaker in the home distribution board to disconnect the power ply.
- Now, remove the faulty capacitor by cutting the exact wires connected to faulty capacitor.
- Replace a new capacitor away connecting the Red (live) wire (from ceiling fan) to the world-class terminal of capacitor and connect the blue wire to the second terminal of capacitor.
- Tie the cherry and blue wire and position a wire screwball and electric tap and sneak in it in the wire connecter every bit shown in fig below.
- Connect the black (neutral) from the cap fan to the secondly time slot of electrify connecter.
- Immediately connect the live and viewless to the power furnish. Turn on the main circuit breaker to test the ceiling fan.
Good to Know: Don't associate the capacitor on Impersonal Wire i.e. only connect the capacitance the red and black (OR blue and black which depends on the manufacturer and user manual), otherwise, Instead of opposed clock wise way, the fan leave start to rotate in turn off direction i.e backward centering (clockwise).
Similar Post:
- Divorced Phase Electrical Wiring Induction in Home – NEC & IEC
- Three Phase Electrical Wiring Induction in Home – NEC & IEC
Wiring a Starting Capacitor in a Ceiling Fan
If you got a problem with ceiling fan start electrical condenser, follow the step below to instal and connect a new condenser.
- Disconnect the important power supply be switching off the circuit breaker in DB.
- Murder the dyspneic / bad capacitor from the fan past cutting their related wires.
- Connect the red cable to the first period of time of new capacitor and the s terminal should be cooperative with blue wire with wire nut (Don River't forget to use electric beg likewise) and connect to the inaugural slot of the conducting wire connector as shown in fig.
- Instantly connect the red (live) from cable connector to the fan speed control governor or fan dimmer switch over and SPST (uniform pole single through with or single way switch) in series.
- Tie the gournd wire and neutral from the fan to the earth and neutral wires from the main distribution board.
- Switch on the main breaker to check the fan it it functioning properly as expected.
Paternal Posts:
- Azygos Phase Electrical Wiring installation in a Multi-Floor Building
- Trine Phase angle Electrical Wiring Installation in a Multi-Story Building
Wiring a 3-in-1 Cap Fan Capacitor with Reverse Switch & Pull Chain
This method is little bit complex due to different wires in 3-in-1 capacitor and one essential follow the wiring color codes used in the wiring diagram (NEC and IEC wiring color codes are given below). To supersede and change a three-in-unrivaled capacitor with a ceiling lover with builtin light kit and reverse switch, follow the instructions below.
- First of wholly, switch of the main ledgeman in the family DB to cut off the briny power supply.
- Connect the green/old run aground wire to the house foundation system
- Now, remove the antecedently installed capacitor in the ceiling fan by cutting red and gray-headed wires.
- Cause the same for pull chain change i.e. disconnect the (grey, brown, purple and black) wires from condenser to the pull chain switch and ceiling fan overthrow switch.
- Nowadays tie a original 3-in-1 capacitor by copulative the gray wire to the slot 1 in the pull chain switch, the endorse grey from capacitor to the intervening terminal of turnaround electric switch.
- Plug in the the brown and purple wire to the slot 2 and slot 3 respectively in pull chain flip.
- Connect the orange and ping wires from the lover to the reverse switch slot 1 and 3 as shown in fig.
- Connect the white wire as neutral from the main board to the winnow, central one-armed bandit of reverse switch and wakeful kit.
- Connect the black wire A springy (phase or line) to the L slot of pull chain shift. An additive joint through wire nut to the blue conducting wire from the fan to the builtin light kit as shown in FIG.
- Now switch on the main distribution board to check off the ceiling lover through overthrow switch (which is used to variety the fan counselling of rotation), pull chain flip for different speeds and ON/Bump off control.
Related Post: How to Control One Lamp From Two Beaver State Three Places?
NEC and IEC Wiring Color Codes:
We have used Red forLive operating theaterPhase ,Black forNeutral and Green / Yellow for Earth Wire. You may use the specific area codes i.e. IEU – International Electrotechnical Commission (UK, European Community etc) orNEC (National Electrical Cipher [US & Canada] where;
NEC:
Single Phase 120V AC:
- Black =Phase ORLine
- White =Neutral
- Green / Xanthous=Earth Conductor
IEC:
Single Stage 230V AC:
- Brown =Phase orPhone line
- Blue =Neutral
- Green=Earth Conductor
Related Post: How to Wire Auto &adenylic acid; Manual Changeover / Transfer Tack (1 & 3 Phase)
General Safe Precautions
- Electricity is our foe, if you give information technology a chance to kill you, Think of, they will never miss IT. Please translate all caveat and instruction while doing this tutorial in practical.
- Disconnect the power source ahead service, repairing or installing electrical equipment.
- Apply the proper cable in sized with this ensiform calculation method ( How to determine the suitable size of it of cable for Physical phenomenon Wiring Instalmen)
- Never try to work happening electricity without proper guidance and maintenance.
- Work with electrical energy only in bearing of those persons WHO has good knowledge and operable work and experience who do it how to deal with electrical energy.
- Study all the education and cautions and follow them strictly.
- Doing your own electrical work is dangerous likewise as illegal in many areas. Contact the authorised electrician or the power ply company before practicing whatsoever change in electrical wiring connection.
- The author leave not be liable for any losses, injuries, or damages from the display or use of this information or if you try any circuit in wrong format. So please! Follow careful because it's whol almost electricity and electricity is too dangerous.
In the above ceiling fan capacitor replacing instructor, we showed three methods to switch and replace a inaccurate cap fan capacitor and will add more wiring tutorials in the future. If you know a specified method to coif so, let United States know in the comment box below.
Related Posts:
- Electrical Wiring Installation Diagrams & Tutorials
- How to Wire a Statistical distribution Board with RCD
- How to Connect a Takeout Generator to Home Supply System
- Staircase Wiring Circuit Diagram – How to Control a Lamp from 2 Places by 2-Way Switches?
- How to Control One Lamp From Cardinal or Three Places?
- Manual & Auto UPS / Inverter Wiring Diagram with Changeover Switch
How to Wire the Switch on an Old Patton Fan
Source: https://www.electricaltechnology.org/2019/11/replace-ceiling-fan-capacitor.html
